ADS-EMU Wiederholung Genauigkeit Leveling Klipper

Dieses Thema hat 2 Antworten sowie 1 Teilnehmer und wurde zuletzt vor vor 1 Jahr, 11 Monaten von dennis02121978 aktualisiert. This post has been viewed 704 times

Ansicht von 3 Beiträgen – 1 bis 3 (von insgesamt 3)

Autor

Beiträge
2. Januar 2023 um 11:46 Uhr #889
dennis02121978
Administrator
Hier könnt Ihr ein Screenshot sehen wo ich gerade einen Test des Emulators (neue Firmware) mit Klipper gemacht habe.

Wie man gleich erkennen kann sind wir im 1000stel Bereich was für den 3D Druck schon übertrieben ist.
2. Januar 2023 um 13:19 Uhr #890
dennis02121978
Administrator
12:33:59
// Profile [default] removed from storage for this session.
// The SAVE_CONFIG command will update the printer
// configuration and restart the printer
12:34:20 $ BED_MESH_PROFILE SAVE=“RF2000″
12:34:20 $ BED_MESH_PROFILE REMOVE=“default“
12:34:20 $ SAVE_CONFIG
12:34:20 // Bed Mesh state has been saved to profile [RF2000]
// for the current session. The SAVE_CONFIG command will
// update the printer config file and restart the printer.
12:34:20 // No profile named [default] to remove
12:34:21 // Klipper state: Disconnect
12:34:25 // Klipper state: Ready
12:34:29 $ SET_HEATER_TEMPERATURE HEATER=extruder TARGET=200
12:34:31 $ SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=65
12:34:39 $ G28
12:34:49 $ QUERY_PROBE
12:34:50 // probe: open
12:34:50 $ QUERY_PROBE
12:34:51 // probe: open
12:34:51 $ QUERY_PROBE
12:34:51 // probe: open
12:34:58 $ BED_MESH_CALIBRATE
12:35:05 // probe at 0.000,55.000 is z=-0.144141
12:35:11 // probe at 0.000,55.000 is z=-0.141797
12:35:17 // probe at 0.000,55.000 is z=-0.141016
12:35:29 // probe at 39.001,55.000 is z=0.000391
12:35:35 // probe at 39.001,55.000 is z=0.000000
12:35:40 // probe at 39.001,55.000 is z=0.003125
12:35:51 // probe at 78.002,55.000 is z=0.079297
12:35:57 // probe at 78.002,55.000 is z=0.079688
12:36:03 // probe at 78.002,55.000 is z=0.081250
12:36:13 // probe at 117.003,55.000 is z=0.104688
12:36:19 // probe at 117.003,55.000 is z=0.105469
12:36:25 // probe at 117.003,55.000 is z=0.107813
12:36:35 // probe at 155.997,55.000 is z=0.145703
12:36:41 // probe at 155.997,55.000 is z=0.147656
12:36:46 // probe at 155.997,55.000 is z=0.148438
12:36:56 // probe at 194.998,55.000 is z=0.134375
12:37:02 // probe at 194.998,55.000 is z=0.134766
12:37:08 // probe at 194.998,55.000 is z=0.134766
12:37:19 // probe at 194.998,139.998 is z=0.080469
12:37:25 // probe at 194.998,139.998 is z=0.079688
12:37:30 // probe at 194.998,139.998 is z=0.082031
12:37:41 // probe at 155.997,139.998 is z=0.106641
12:37:47 // probe at 155.997,139.998 is z=0.107422
12:37:52 // probe at 155.997,139.998 is z=0.107031
12:38:03 // probe at 117.003,139.998 is z=0.127734
12:38:08 // probe at 117.003,139.998 is z=0.127344
12:38:14 // probe at 117.003,139.998 is z=0.126953
12:38:24 // probe at 78.002,139.998 is z=0.112500
12:38:30 // probe at 78.002,139.998 is z=0.112891
12:38:36 // probe at 78.002,139.998 is z=0.111328
12:38:47 // probe at 39.001,139.998 is z=0.015234
12:38:52 // probe at 39.001,139.998 is z=0.014453
12:38:58 // probe at 39.001,139.998 is z=0.016406
12:39:09 // probe at -0.000,139.998 is z=-0.020312
12:39:15 // probe at -0.000,139.998 is z=-0.022266
12:39:21 // probe at -0.000,139.998 is z=-0.023047
12:39:32 // probe at -0.000,225.002 is z=0.242969
12:39:38 // probe at -0.000,225.002 is z=0.239063
12:39:44 // probe at -0.000,225.002 is z=0.237500
12:39:53 // probe at 39.001,225.002 is z=0.238281
12:39:58 // probe at 39.001,225.002 is z=0.241406
12:40:04 // probe at 39.001,225.002 is z=0.241797
12:40:13 // probe at 78.002,225.002 is z=0.169531
12:40:19 // probe at 78.002,225.002 is z=0.171094
12:40:25 // probe at 78.002,225.002 is z=0.172266
12:40:35 // probe at 117.003,225.002 is z=0.120313
12:40:40 // probe at 117.003,225.002 is z=0.122266
12:40:46 // probe at 117.003,225.002 is z=0.122266
12:40:57 // probe at 155.997,225.002 is z=0.106641
12:41:02 // probe at 155.997,225.002 is z=0.107422
12:41:08 // probe at 155.997,225.002 is z=0.106250
12:41:19 // probe at 194.998,225.002 is z=0.059766
12:41:24 // probe at 194.998,225.002 is z=0.062109
12:41:30 // probe at 194.998,225.002 is z=0.062891
12:41:30 // Mesh Bed Leveling Complete
12:41:30 // Bed Mesh state has been saved to profile [default]
// for the current session. The SAVE_CONFIG command will
// update the printer config file and restart the printer.
12:41:37 $ SAVE_CONFIG
12:41:38 // Klipper state: Disconnect
12:41:42 // Klipper state: Ready

Da hier noch + Werte waren musste ich den Endstop in Z-Home höher nehmen (früher auslösen) um auf negative Werte zu kommen. Vorsicht wegen dem Endschalter (nicht zu Hoch)
2. Januar 2023 um 14:33 Uhr #892
dennis02121978
Administrator
14:20:43 $BED_MESH_CALIBRATE
14:20:52 // probe at 0.000,55.000 is z=-0.368359
14:20:58 // probe at 0.000,55.000 is z=-0.368359
14:21:04 // probe at 0.000,55.000 is z=-0.366016

14:21:18 // probe at 39.001,55.000 is z=-0.231641
14:21:24 // probe at 39.001,55.000 is z=-0.231641
14:21:30 // probe at 39.001,55.000 is z=-0.233594

14:21:43 // probe at 78.002,55.000 is z=-0.155078
14:21:49 // probe at 78.002,55.000 is z=-0.155859
14:21:54 // probe at 78.002,55.000 is z=-0.158203

14:22:07 // probe at 117.003,55.000 is z=-0.093359
14:22:13 // probe at 117.003,55.000 is z=-0.090625
14:22:18 // probe at 117.003,55.000 is z=-0.090234

14:22:31 // probe at 155.997,55.000 is z=-0.077344
14:22:37 // probe at 155.997,55.000 is z=-0.082812
14:22:42 // probe at 155.997,55.000 is z=-0.080469

14:22:54 // probe at 194.998,55.000 is z=-0.074609
14:23:00 // probe at 194.998,55.000 is z=-0.074219
14:23:06 // probe at 194.998,55.000 is z=-0.074219

14:23:19 // probe at 194.998,139.998 is z=-0.148828
14:23:25 // probe at 194.998,139.998 is z=-0.149609
14:23:31 // probe at 194.998,139.998 is z=-0.149219

14:23:44 // probe at 155.997,139.998 is z=-0.102344
14:23:49 // probe at 155.997,139.998 is z=-0.102734
14:23:55 // probe at 155.997,139.998 is z=-0.101562

14:24:07 // probe at 117.003,139.998 is z=-0.121484
14:24:13 // probe at 117.003,139.998 is z=-0.121094
14:24:19 // probe at 117.003,139.998 is z=-0.121094

14:24:32 // probe at 78.002,139.998 is z=-0.124219
14:24:37 // probe at 78.002,139.998 is z=-0.128906
14:24:43 // probe at 78.002,139.998 is z=-0.128906

14:24:56 // probe at 39.001,139.998 is z=-0.223047
14:25:02 // probe at 39.001,139.998 is z=-0.219922
14:25:08 // probe at 39.001,139.998 is z=-0.219141

14:25:21 // probe at -0.000,139.998 is z=-0.248047
14:25:27 // probe at -0.000,139.998 is z=-0.248047
14:25:33 // probe at -0.000,139.998 is z=-0.248047

14:25:48 // probe at -0.000,225.002 is z=-0.281250
14:25:53 // probe at -0.000,225.002 is z=-0.280078
14:25:59 // probe at -0.000,225.002 is z=-0.280078

14:26:13 // probe at 39.001,225.002 is z=-0.222656
14:26:19 // probe at 39.001,225.002 is z=-0.222656
14:26:25 // probe at 39.001,225.002 is z=-0.223437

14:26:38 // probe at 78.002,225.002 is z=-0.161719
14:26:44 // probe at 78.002,225.002 is z=-0.160156
14:26:49 // probe at 78.002,225.002 is z=-0.160547

14:27:02 // probe at 117.003,225.002 is z=-0.103125
14:27:08 // probe at 117.003,225.002 is z=-0.105078
14:27:14 // probe at 117.003,225.002 is z=-0.105078

14:27:26 // probe at 155.997,225.002 is z=-0.086328
14:27:32 // probe at 155.997,225.002 is z=-0.088281
14:27:37 // probe at 155.997,225.002 is z=-0.088281

14:27:50 // probe at 194.998,225.002 is z=-0.124609
14:27:56 // probe at 194.998,225.002 is z=-0.123437
14:28:01 // probe at 194.998,225.002 is z=-0.125781

14:28:01 // Mesh Bed Leveling Complete
14:28:01 // Bed Mesh state has been saved to profile [default]
// for the current session. The SAVE_CONFIG command will
// update the printer config file and restart the printer.

Diese Daten sind nicht be oder überarbeitet außer Leerzeile für bessere Lesbarkeit eingefügt. Dieses Leveling kann ich auch gerne per Anydesk zeigen (LIVE) im Fall jemand glaubt mir das nicht.

Hier noch das Bild dazu
Autor

Beiträge

Ansicht von 3 Beiträgen – 1 bis 3 (von insgesamt 3)

Du musst angemeldet sein, um auf dieses Thema antworten zu können.